开启GD32的时钟旁路模式，再打开OSCOUT引脚重映射模式，即PD1脚映射到该OSCOUT引脚。程序无法执行，且智能下载一次，第二次下载需要双击两次复位按键。但如果我使用内部高速时钟就PD1脚就可以成功映射到OSCOUT上，程序正常型。环境：keil5.37
芯片：GD32F105RCT6 64脚
库：   HAL库

希望懂的朋友解答一下。谢谢！
void GpioInit(void)
{
          __HAL_RCC_GPIOC_CLK_ENABLE();
    __HAL_AFIO_REMAP_PD01_ENABLE();
    GPIO_InitTypeDef GPIO_InitStruct = {0};
    GPIO_InitStruct.Pin = GPIO_PIN_1;
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
    HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);

    HAL_GPIO_WritePin(GPIOD, GPIO_PIN_1, GPIO_PIN_RESET);  //OUT12_PIN=H_Level   控制EN12脚  2# 反馈信号
}//PD1引脚初始化



void SystemClock_Config(void)
{
    RCC_OscInitTypeDef RCC_OscInitStruct = {0};
    RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
    RCC_PeriphCLKInitTypeDef PeriphClkInit = {0};

    /** Initializes the CPU, AHB and APB busses clocks
    */
//外部高速时钟：程序不能执行
//    RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
//    RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS;
//    RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1;
//    RCC_OscInitStruct.HSIState = RCC_HSI_ON;
//    RCC_OscInitStruct.Prediv1Source = RCC_PREDIV1_SOURCE_HSE;
//    RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
//    RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
//    RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL8;
//    RCC_OscInitStruct.PLL2.PLL2State = RCC_PLL_NONE;
               
//内部高速时钟：程序正常运行       
    RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
    RCC_OscInitStruct.HSIState = RCC_HSI_ON;
    RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
    RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI_DIV2;
    RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL8;
    RCC_OscInitStruct.PLL2.PLL2State = RCC_PLL_NONE;

    if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
    {
        Error_Handler();
    }
    /** Initializes the CPU, AHB and APB busses clocks
    */
    RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                                  |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
    RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
    RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
    RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
    RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;

    if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
    {
        Error_Handler();
    }
    PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC;
    PeriphClkInit.AdcClockSelection = RCC_ADCPCLK2_DIV8;
    if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK)
    {
        Error_Handler();
    }
    /** Configure the Systick interrupt time
    */
    __HAL_RCC_PLLI2S_ENABLE();
}