哈哈，前阵子画了板ＣＨ３７４的评估版，焊了块ＣＨ３７２做ＵＳＢ设备试验．
ＣＨ３７２在外置固件下枚举成Ｕ盘，Ｃ语言版本很早就搞定了．
网上遇一网友，说只会汇编，打赌说我无法搞出个汇编版的．
俺就不信这个邪，苦战半夜，终于搞定
源程序如下：
;古老牌U盘汇编版
;CH372+STC89C54单片机
;作者邮箱:xg_2004_sy@126.com
$INCLUDE (CH375INC.ASM)
STACK EQU 80H ;堆栈区栈顶(向上延伸)
;
; 需要主程序定义的参数
CH375_CMD_PORT EQU 0xB100 ;CH375命令口的地址,地址译码后自动片选
CH375_DAT_PORT EQU 0xB000 ;CH375命令口的地址,地址译码后自动片选
;
CH375_CON_ACT BIT P1.2
VAR_NeedTransBlockCount Data 30h
VAR_TransCompleteBlockCount Data 31H
VAR_MainRXDataPackCount Data 32h
VAR_ucTransFinishPageCount DATA 33H
VAR_ucNeedTransPageCount DATA 34
VAR_ExtSRAMDataLocationPoint_L Data 35H
VAR_ExtSRAMDataLocationPoint_H Data 36H
VAR_CSW_BYTE_4 DATA 37H
VAR_CSW_BYTE_5 DATA 38H
VAR_CSW_BYTE_6 DATA 39H
VAR_CSW_BYTE_7 DATA 3AH
var_EP2_UP_STATUS DATA 3BH ;上传数据状态切换变量
CMD_BUFFER DATA 3FH ;命令包缓冲区,本程序约定命令包长度为CONST_CMD_LEN
CBW_Buffer DATA 10H ;cbW占用数据长度为12
VAR_SETUP_REQUEST EQU 72H ;USB请求码
VAR_SETUP_LENGTH EQU 73H ;后续数据长度
VAR_SETUP_DESCR EQU 74H ;描述符偏移地址
VAR_SN_STRING EQU 75H ;产品序列号字符串缓冲区,ANSI字符串
VAR_USB_ADDRESS EQU 76H
Reload_Count EQU 0F3H
c_Char_0 EQU 30H
c_Char_1 EQU 31H
c_Char_2 EQU 32H
c_Char_3 EQU 33H
c_Char_4 EQU 34H
c_Char_5 EQU 35H
c_Char_6 EQU 36H
c_Char_7 EQU 37H
c_Char_8 EQU 38H
c_Char_9 EQU 39H
; 定义位标志
CH375_CON_FLAG BIT 2FH.0 ;375芯片配置完成标志
VAR_MainRXDataStatusMac Bit 2FH.1 ;主端点数据接收状态机标志
;
;****************************************************************************
;主程序
ORG 0000H ;复位后单片机入口
LJMP START
ORG 0013H ;CH375中断
LJMP CH375_INTER
ORG 0100H
;---------------------------------------------------------------------------------
Initial_UART:
Mov SCON,#50h
Mov TMOD,#21h
Mov TH1,#Reload_Count
Mov TL1,#Reload_Count
ORL PCON,#80h
SETB TR1 ;启动定时器
Ret
UART_Send_Char: ;通过串口发送字符,待发送的字符在ACC中
CLR TI
Mov SBUF,A
Uart_Wait_Send_Finish:
JNB TI,UART_Wait_Send_Finish
CLR TI
Ret
;---------------------------------------------------------------------------------
START:
; 以下初始化指令不是必要的,将单片机恢复为默认状态
CLR EA ;关中断
MOV SP,#STACK ;置堆栈初值
MOV A,#0FFH
MOV P0,A
MOV P1,A ;清端口状态
MOV P2,A
MOV P3,A
CLR A
MOV IE,A ;清中断允许控制寄存器
MOV IP,A ;清中断优先级控制寄存器
MOV PSW,A ;清程序状态字
MOV TCON,A ;清定时器/计数器控制寄存器
MOV TMOD,A ;清定时器/计数器工作方式寄存器
MOV PCON,A ;清电源控制寄存器
MOV R7,#0FFH
CALL DELAY_MS ;延时等待CH375初始化完成
; 初始化
Call Initial_UART
UART_SendTestChar:
Mov a,#c_Char_0
call UART_Send_Char
Mov a,#0DH
call UART_Send_Char
Mov a,#0AH
call UART_Send_Char
Mov a,#c_Char_8
call UART_Send_Char
Mov a,#0DH
call UART_Send_Char
Mov a,#0AH
call UART_Send_Char
; AJMP UART_SendTestChar
MOV R6,#0;
MOV R7,#0;
MOV DPTR,#0
ACALL READ_FLASH_SECTOR
MOV DPTR,#0
MOV R4,#4
TEST_SEND_FLASHSECTOR_PAGE_LOOP:
MOV R5,#128
TEST_SEND_FLASHSECTOR_BYTE_LOOP:
MOVX A,@DPTR
call UART_Send_Char
INC DPTR
DJNZ R5,TEST_SEND_FLASHSECTOR_BYTE_LOOP
DJNZ R4,TEST_SEND_FLASHSECTOR_PAGE_LOOP
CALL CH375_DisConnect ;配置为断开USB连接的状态
CALL CH375_INIT ;初始化
call Init_EP2_FUNC_VAlRegister
setb EA
ljmp $ ;主程序
;
;-------------------------------------------------------------------
;------ STC MCU Flash PGM --------------------------------
ISP_DATA DATA 0E2H
ISP_ADDRH DATA 0E3H
ISP_ADDRL DATA 0E4H
ISP_CMD DATA 0E5H
ISP_TRIG DATA 0E6H
ISP_CONTR DATA 0E7H
;定义Flash操作等待时间性
ENABLE_ISP EQU 80H
MCU_FLASH_START_ADDRESS_HIGH EQU 80H
;读一字节
;调用前需打开IAP功能
;入口：DPTR = 字节地址
;返回：A = 读出字节
MCU_FLASH_READ_BYTE:
MOV ISP_CONTR,#ENABLE_ISP
MOV ISP_CMD,#01
MOV ISP_ADDRH,DPH
MOV ISP_ADDRL,DPL
CLR EA
MOV ISP_TRIG,#46H
MOV ISP_TRIG,#0B9H
NOP
MOV A,ISP_DATA
SETB EA
;Now in processing(CPU will hart here before completing)
; ACALL IAP_Disable
RET
;字节编程
;调用前需打开IAP功能
;入口：DPTR = 字节地址，A= 须编程字节的数据
MCU_FLASH_WRITE_BYTE:
MOV ISP_CONTR,#ENABLE_ISP
MOV ISP_CMD,#02
MOV ISP_ADDRH,DPH
MOV ISP_ADDRL,DPL
MOV ISP_DATA,A
CLR EA
MOV ISP_TRIG,#46H
MOV ISP_TRIG,#0B9H
NOP
SETB EA
;Now in processing(CPU will hart here before completing)
ACALL IAP_Disable
RET
;擦除扇区
;入口：DPTR = 扇区地址
MCU_FLASH_ERASE_SECTOR:
MOV ISP_CONTR,#ENABLE_ISP
MOV ISP_CMD,#03
MOV ISP_ADDRH,DPH
MOV ISP_ADDRL,DPL
CLR EA
MOV ISP_TRIG,#46H
MOV ISP_TRIG,#0B9H
NOP
SETB EA
;Now in processing(CPU will hart here before completing)
; ACALL IAP_Disable
RET
IAP_Disable:
MOV ISP_CONTR,#0
MOV ISP_CMD,#0
MOV ISP_TRIG,#0
RET
;写数据到扇区
;入口地址 （R6R7）扇区号
;DPTR指向数据缓冲区，数据长度恒定为512字节
WRITE_FLASH_SECTOR:
PUSH DPH ;数据缓冲区指针入栈保护
PUSH DPL
MOV A,R7
ADD A,0E0H ;A =A*2
ADD A,#MCU_FLASH_START_ADDRESS_HIGH
MOV R6,A
MOV R7,#00 ;完成起始地址的计算 数据在R6,R7中
MOV DPH,R6
MOV DPL,R7
ACALL MCU_FLASH_ERASE_SECTOR
MOV R3,#4
WRITE_SECTOR_LOOP_WRITE_PAGE:
MOV R4,#128;
WRITE_SECTOR_LOOP_Write_Byte:
POP DPL
POP DPH
MOVX A,@DPTR;
INC DPTR
PUSH DPH
PUSH DPL
MOV DPH,R6
MOV DPL,R7
ACALL MCU_FLASH_WRITE_BYTE
INC DPTR
MOV R7,DPL
MOV R6,DPH
DJNZ R4,WRITE_SECTOR_LOOP_Write_Byte
DJNZ R3,WRITE_SECTOR_LOOP_Write_Page
POP DPL
POP DPH
RET
;从扇区读数据到缓冲区
;入口地址 （R6R7）扇区号
;DPTR指向数据缓冲区，数据长度恒定为512字节
READ_FLASH_SECTOR:
PUSH DPH ;数据缓冲区指针入栈保护
PUSH DPL
MOV A,R7
ADD A,0E0H ;A =A*2
ADD A,#MCU_FLASH_START_ADDRESS_HIGH
MOV R6,A
MOV R7,#00 ;完成起始地址的计算 数据在R6,R7中
MOV DPH,R6
MOV DPL,R7
MOV R3,#4
READ_SECTOR_LOOP_READ_PAGE:
MOV R4,#128;
READ_SECTOR_LOOP_READ_Byte:
MOV DPH,R6
MOV DPL,R7
LCALL MCU_FLASH_READ_BYTE
INC DPTR
MOV R7,DPL
MOV R6,DPH
POP DPL
POP DPH
MOVX @DPTR,A;
INC DPTR
PUSH DPH
PUSH DPL
DJNZ R4,READ_SECTOR_LOOP_READ_Byte
DJNZ R3,READ_SECTOR_LOOP_READ_PAGE
POP DPL
POP DPH
RET
;------------------Flash PGM END----------------------------------------
; 输出命令码给CH375
; 输入: ACC 为命令码
; 输出: DPTR 为数据口
; USE: ACC, DPTR
WR_CMD_TO_375:
MOV DPTR,#CH375_CMD_PORT ;命令口地址
MOVX @DPTR,A ;设置USB工作模式
NOP ;如果时钟频率低于20MHz则无需该指令延时,高于30MHz要多加2条指令
MOV DPTR,#CH375_DAT_PORT ;数据口地址
RET
;
; 初始化子程序
; USE: ACC, R7, DPTR
CH375_INIT:
MOV A,#CMD_SET_USB_MODE ;设置USB工作模式
CALL WR_CMD_TO_375 ;输出命令码
; MOV A,#02H ;设置为内置固件模式
MOV A,#01H ;设置为外置固件模式
MOVX @DPTR,A ;设置为使用内置固件的USB设备方式
NOP ;如果时钟频率低于16MHz则无需该指令延时
NOP
CH375_INIT_WT:
MOVX A,@DPTR ;返回操作状态,也可以等待20uS
XRL A,#CMD_RET_SUCCESS
JNZ CH375_INIT_WT ;等待操作成功,通常需要等待10uS-20uS
; 下述三条指令用于启用中断
CLR IT1 ;置外部信号为低电平触发
SETB PX1 ;置高优先级
CLR IE1 ;清中断标志
SETB EX1 ;允许CH375中断
RET
;**************************************************************************************
CH375_DisConnect:
MOV A,#CMD_SET_USB_MODE ;设置USB工作模式
CALL WR_CMD_TO_375 ;输出命令码
MOV A,#00H ;设置为未配置模式
MOVX @DPTR,A ;设置为使用内置固件的USB设备方式
NOP ;如果时钟频率低于16MHz则无需该指令延时
NOP
CH375_DisConnect_WT:
MOVX A,@DPTR ;返回操作状态,也可以等待20uS
XRL A,#CMD_RET_SUCCESS
JNZ CH375_DisConnect_WT ;等待操作成功,通常需要等待10uS-20uS
; 下述三条指令用于启用中断
CLR IT1 ;置外部信号为低电平触发
SETB PX1 ;置高优先级
CLR IE1 ;清中断标志
SETB EX1 ;允许CH375中断
RET
;写代码定间的数据到EP2的端点
;数据长度在R4中,数据缓冲区指针在DPTR中,采用MOVC取数
CH375_EP2_WRITE_CODEDATA:
MOV R6,DPL
MOV R7,DPH ; SAVE DATA POINT
MOV A,#CMD_WR_USB_DATA7 ;发出写上传端点命令
CALL WR_CMD_TO_375
MOV A,R4
MOVX @DPTR,A ;写数据长度
JZ CH375_EP2_WRITE_CODE_FINISH ;长度为0
EP2_WRITE_CODE_LOOP1:
MOV DPL,R6 ;Get Data Point from backup DPTR Image
MOV DPH,R7
CLR A
MOVC A,@A+DPTR
INC DPTR
MOV R6,DPL
MOV R7,DPH ; SAVE DATA POINT
MOV DPTR,#CH375_DAT_PORT
MOVX @DPTR,A
DJNZ R4,EP2_WRITE_CODE_LOOP1
CH375_EP2_WRITE_CODE_FINISH:
RET
;---------------------------------------------------------------------------------------
;写数据空间的内容到CH372的EP端点
;数据长度在R4中,数据缓冲区指针在DPTR中,采用MOVX取数
CH375_EP2_WRITE_XDATA:
MOV R6,DPL
MOV R7,DPH ; SAVE DATA POINT
MOV A,#CMD_WR_USB_DATA7 ;发出写上传端点命令
CALL WR_CMD_TO_375
MOV A,R4
MOVX @DPTR,A ;写数据长度
JZ CH375_EP2_WRITE_CODE_FINISH ;长度为0
EP2_WRITE_XDATA_LOOP1:
MOV DPL,R6 ;Get Data Point from backup DPTR Image
MOV DPH,R7
MOVX A,@DPTR
INC DPTR
MOV R6,DPL
MOV R7,DPH ; SAVE DATA POINT
MOV DPTR,#CH375_DAT_PORT
MOVX @DPTR,A
DJNZ R4,EP2_WRITE_XDATA_LOOP1
CH375_EP2_WRITE_XDATA_FINISH:
RET
;----------------------------------------------------------------------------------------
c_EP2_UPSTATUS_TRANSMIT_IDLE EQU 00H
c_EP2_UPSTATUS_TRANSMIT_CSW EQU 01H
c_EP2_UPSTATUS_TRANSMIT_STANDPAGE EQU 02H
c_EP2_UPSTATUS_TRANSMIT_SHORTPAGE EQU 03H
;CMD_INQUIRY_FUNCTION
FUNC_SCSI_CMD10_INQUIRY:
MOV DPTR,#USB_InquiryData_TAB
MOV R4,#36
CALL CH375_EP2_WRITE_CODEDATA
MOV var_EP2_UP_STATUS,#c_EP2_UPSTATUS_TRANSMIT_CSW ;发送完数据发状态
RET
;CMD_READ_CAPACITY
FUNC_SCSI_CMD25_READ_CAPACITY:
MOV DPTR,#USB_UDISK_Capacity
MOV R4,#8
CALL CH375_EP2_WRITE_CODEDATA
MOV var_EP2_UP_STATUS,#c_EP2_UPSTATUS_TRANSMIT_CSW ;发送完数据发状态
RET
;CMD_READ_FORMAT_CAPACITIES
FUNC_SCSI_CMD23_READ_FORMAT_CAPACITYIES:
MOV DPTR,#USB_UDISK_FORMAT_Capaities
MOV R4,#20
CALL CH375_EP2_WRITE_CODEDATA
MOV var_EP2_UP_STATUS,#c_EP2_UPSTATUS_TRANSMIT_CSW ;发送完数据发状态
RET
;MCD00_TEST_UNITE_READY
FUNC_SCSI_CMD00_TEST_UNITE_READY:
ACALL TransitCSW
RET
;CMD_MODE_SENSE
FUNC_SCSI_CMD1A_MODE_SENSE:
MOV A,CBW_Buffer+2 ;CBW[2] Value send to ACC
CJNE A,#1CH,MODE_SENSE_NEXT1
MOV DPTR,#USB_UDISK_MODE_SENSE_TPP
MOV R4,#18
CALL CH375_EP2_WRITE_CODEDATA
AJMP MODE_SENSE_END
MODE_SENSE_NEXT1:
CJNE A,#3FH,MODE_SENSE_NEXT2
MOV DPTR,#USB_UDISK_MODE_SENSE_ALL
MOV R4,#12
CALL CH375_EP2_WRITE_CODEDATA
AJMP MODE_SENSE_END
MODE_SENSE_NEXT2:
MOV DPTR,#USB_UDISK_MODE_SENSE_ZERO
MOV R4,#8
CALL CH375_EP2_WRITE_CODEDATA
AJMP MODE_SENSE_END
MODE_SENSE_END:
MOV var_EP2_UP_STATUS,#c_EP2_UPSTATUS_TRANSMIT_CSW ;发送完数据发状态
RET
;CMD28_READ10
FUNC_SCSI_CMD28_READ10:
MOV A, CBW_Buffer+8
JNZ CMD28_Need_Trans_Data_Package
ACALL TransitCSW
AJMP CMD28_READ10_END
CMD28_Need_Trans_Data_Package:
MOV VAR_NeedTransBlockCount,A
MOV VAR_TransCompleteBlockCount,#0
MOV R7, CBW_Buffer+5
MOV R6, CBW_Buffer+4
MOV VAR_ucTransFinishPageCount,#0
MOV VAR_ucNeedTransPageCount,#8
MOV DPTR,#0
ACALL READ_FLASH_SECTOR
MOV var_EP2_UP_STATUS,#c_EP2_UPSTATUS_TRANSMIT_STANDPAGE ;发送完数据发状态
MOV DPTR,#0
MOV R4,#64
CALL CH375_EP2_WRITE_XDATA
INC VAR_ucTransFinishPageCount
CMD28_READ10_END:
RET
;CMD2A_WRITE10:
FUNC_SCSI_CMD2A_WRITE10:
SETB VAR_MainRXDataStatusMac
MOV A, CBW_Buffer+8
MOV VAR_NeedTransBlockCount,A
MOV VAR_MainRXDataPackCount,#0
MOV VAR_TransCompleteBlockCount,#0
JNZ CMD2A_WRITE10_FINISH
CLR VAR_MainRXDataStatusMac
CMD2A_WRITE10_FINISH:
RET
;---------------------------------------------------------------------------------------------
CMD12_INQUIRY EQU 12H
CMD1A_MODE_SENSE EQU 1AH
CMD28_READ10 EQU 28H
CMD25_READ_CAPACITY EQU 25H
CMD23_READ_FORMAT_CAPACITIES EQU 23H
CMD00_TEST_UNIT_READY EQU 00H
CMD2F_VERIRY EQU 2FH
CMD2A_WRITE10 EQU 2AH
CMD1E_MEDIUM_REMOVAL EQU 1EH
;对EP2接收到的CBW进行解析和处理
;R4为数据长度
;数据内容在公共缓冲区中
EP2CMDProcess:
MOV R0,#CMD_BUFFER+4 ;拷贝CSW内容
MOV A,@R0
MOV VAR_CSW_BYTE_4,A
iNC R0
MOV A,@R0
MOV VAR_CSW_BYTE_5,A
iNC R0
MOV A,@R0
MOV VAR_CSW_BYTE_6,A
iNC R0
MOV A,@R0
MOV VAR_CSW_BYTE_7,A
MOv R4,#12
MOV R0,#CMD_BUFFER+15 ;拷贝UFI内容
MOV R1,#CBW_Buffer
COPY_CBW_LOOP_1:
MOV A,@R0
MOV @R1,A
INC R0
INC R1
DJNZ R4,COPY_CBW_LOOP_1
Mov a,#c_Char_1
call UART_Send_Char
Mov a,#c_Char_1
call UART_Send_Char
MOV A,CBW_Buffer
call UART_Send_Char
Mov a,#0DH
call UART_Send_Char
Mov a,#0AH
call UART_Send_Char
MOV A,CBW_Buffer
CJNE A,#CMD12_INQUIRY,NO_CMD10_SEGMENT
CALL FUNC_SCSI_CMD10_INQUIRY
AJMP EP2_CMD_END
NO_CMD10_SEGMENT: CJNE A,#CMD25_READ_CAPACITY,NO_CMD25_SEGMENT
CALL FUNC_SCSI_CMD25_READ_CAPACITY
AJMP EP2_CMD_END
NO_CMD25_SEGMENT: CJNE A,#CMD23_READ_FORMAT_CAPACITIES,NO_CMD23_SEGMENT
CALL FUNC_SCSI_CMD23_READ_FORMAT_CAPACITYIES
AJMP EP2_CMD_END
NO_CMD23_SEGMENT: CJNE A,#CMD1A_MODE_SENSE,NO_CMD1A_SEGMENT
CALL FUNC_SCSI_CMD1A_MODE_SENSE
AJMP EP2_CMD_END
NO_CMD1A_SEGMENT: CJNE A,#CMD28_READ10,NO_CMD28_READ10
CALL FUNC_SCSI_CMD28_READ10
AJMP EP2_CMD_END
NO_CMD28_READ10: CJNE A,#CMD00_TEST_UNIT_READY,NO_CMD00_TESTUNITREADY
CALL FUNC_SCSI_CMD00_TEST_UNITE_READY
AJMP EP2_CMD_END
NO_CMD00_TESTUNITREADY: CJNE A,#CMD2A_WRITE10,NO_CMD2A_WRITE10
CALL FUNC_SCSI_CMD2A_WRITE10
AJMP EP2_CMD_END
NO_CMD2A_WRITE10:
EP2_CMD_END:
RET
; Mov a,#c_Char_1
; call UART_Send_Char
; Mov a,#c_Char_0
; call UART_Send_Char
; Mov a,#0DH
; call UART_Send_Char
; Mov a,#0AH
; call UART_Send_Char
;
; Ret
DataFlash_WriteSector:
; Mov a,#c_Char_1
; call UART_Send_Char
; Mov a,#c_Char_1
; call UART_Send_Char
; Mov a,#0DH
; call UART_Send_Char
; Mov a,#0AH
; call UART_Send_Char
MOV R7, CBW_Buffer+5
MOV R6, CBW_Buffer+4
MOV A,R7
ADD A,VAR_TransCompleteBlockCount
MOV R7,A
CLR A
ADDC A,R6
MOV R6,A
MOV DPTR,#0
ACALL WRITE_FLASH_SECTOR
Ret
;-------------------------------------------------------------------------------------------------
TransitCSW:
; Mov a,#c_Char_1
; call UART_Send_Char
; Mov a,#c_Char_2
; call UART_Send_Char
; Mov a,#0DH
; call UART_Send_Char
; Mov a,#0AH
; call UART_Send_Char
; MOV R6,DPL
; MOV R7,DPH ; SAVE DATA POINT
MOV A,#CMD_WR_USB_DATA7 ;发出写上传端点命令
CALL WR_CMD_TO_375
MOV A,#13
MOVX @DPTR,A ;写数据长度
MOV A,#0x55
MOVX @DPTR,A ;写数据长度
MOV A,#0x53
MOVX @DPTR,A ;写数据长度
MOV A,#0x42
MOVX @DPTR,A ;写数据长度
MOV A,#0x53
MOVX @DPTR,A ;写数据长度
MOV A,VAR_CSW_BYTE_4
MOVX @DPTR,A
MOV A,VAR_CSW_BYTE_5
MOVX @DPTR,A
MOV A,VAR_CSW_BYTE_6
MOVX @DPTR,A
|
楼主
标题置顶
标题高亮
