采集两路ADC问题，不用DMA还好，用了DMA。。。

只看该作者 · 2014-1-20 01:31

不知道为什么，没用DMA在上位机能很好的读出ADC1channal 0和 1的数据，可是一用DMA上位机全显示为0了，下面是ADC和DMA的配置，弄了一个晚上弄没好，只好上来求助大神了

#include "pbdata.h"
#define N 20
#define M 2
void RCC_Configuration(void);
void GPIO_Configuration(void);
void NVIC_Configuration(void);
void USART_Configuration(void);
void ADC_Configuration(void);
void DMA_Configuration(void);
void filter(void);

u16 ADCData[M][N];
u16 ADCAVGData[M];

int fputc(int ch,FILE *f)
{
USART_SendData(USART1,(u8)ch);
while(USART_GetFlagStatus(USART1,USART_FLAG_TXE)==RESET);
return ch;
}

int main(void)
{
// u32 ad=0;
u8 i=0;

RCC_Configuration(); //系统时钟初始化
GPIO_Configuration();//端口初始化
USART_Configuration();
NVIC_Configuration();
ADC_Configuration();
DMA_Configuration();

while(1)
{
   filter();
   for(i=0;i<M;i++)
   {
   printf("ad =%f\r\n",3.3/4095*ADCAVGData[i]);//实际电压值
   }
   delay_ms(1000);

}
}

void RCC_Configuration(void)
{
SystemInit();//72m
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA,ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1,ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO,ENABLE);

RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1,ENABLE);
RCC_ADCCLKConfig(RCC_PCLK2_Div6);//12M  最大14M

RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1,ENABLE);
}

void GPIO_Configuration(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
//LED
GPIO_InitStructure.GPIO_Pin=GPIO_Pin_9;//TX
GPIO_InitStructure.GPIO_Speed=GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode=GPIO_Mode_AF_PP;
GPIO_Init(GPIOA,&GPIO_InitStructure);

GPIO_InitStructure.GPIO_Pin=GPIO_Pin_10;//RX
GPIO_InitStructure.GPIO_Mode=GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA,&GPIO_InitStructure);

GPIO_InitStructure.GPIO_Pin=GPIO_Pin_0;//AD
GPIO_InitStructure.GPIO_Mode=GPIO_Mode_AIN;
GPIO_Init(GPIOA,&GPIO_InitStructure);
}

void NVIC_Configuration(void)
{
   NVIC_InitTypeDef NVIC_InitStructure;

NVIC_PriorityGroupConfig(NVIC_PriorityGroup_1);

NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
}

void USART_Configuration(void)
{
USART_InitTypeDef  USART_InitStructure;

USART_InitStructure.USART_BaudRate=9600;
USART_InitStructure.USART_WordLength=USART_WordLength_8b;
USART_InitStructure.USART_StopBits=USART_StopBits_1;
USART_InitStructure.USART_Parity=USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl=USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode=USART_Mode_Rx|USART_Mode_Tx;

USART_Init(USART1,&USART_InitStructure);
USART_ITConfig(USART1,USART_IT_RXNE,ENABLE);
USART_Cmd(USART1,ENABLE);
USART_ClearFlag(USART1,USART_FLAG_TC);
}

void ADC_Configuration(void)
{
ADC_InitTypeDef ADC_InitStructure;
ADC_DeInit(ADC1);
ADC_InitStructure.ADC_Mode=ADC_Mode_Independent;
ADC_InitStructure.ADC_ScanConvMode=ENABLE;
ADC_InitStructure.ADC_ContinuousConvMode=ENABLE;
ADC_InitStructure.ADC_ExternalTrigConv=ADC_ExternalTrigConv_None;
ADC_InitStructure.ADC_DataAlign=ADC_DataAlign_Right;
ADC_InitStructure.ADC_NbrOfChannel=M;

ADC_Init(ADC1,&ADC_InitStructure);

ADC_RegularChannelConfig(ADC1,ADC_Channel_0,1,ADC_SampleTime_239Cycles5);
ADC_RegularChannelConfig(ADC1,ADC_Channel_1,2,ADC_SampleTime_239Cycles5);

ADC_DMACmd(ADC1,ENABLE);

ADC_Cmd(ADC1,ENABLE);

ADC_ResetCalibration(ADC1);
while(ADC_GetResetCalibrationStatus(ADC1));

ADC_StartCalibration(ADC1);
while(ADC_GetCalibrationStatus(ADC1));

ADC_SoftwareStartConvCmd(ADC1,ENABLE);
}

void DMA_Configuration(void)
{
DMA_InitTypeDef DMA_InitStructure;

DMA_DeInit(DMA1_Channel1);

DMA_InitStructure.DMA_PeripheralBaseAddr=(u32)&ADC1->DR;
DMA_InitStructure.DMA_MemoryBaseAddr=(u32)&ADCData;

DMA_InitStructure.DMA_DIR=DMA_DIR_PeripheralSRC;
DMA_InitStructure.DMA_BufferSize=N*M;

DMA_InitStructure.DMA_PeripheralInc=DMA_PeripheralInc_Disable;
DMA_InitStructure.DMA_MemoryInc=DMA_PeripheralInc_Enable;

DMA_InitStructure.DMA_PeripheralDataSize=DMA_PeripheralDataSize_HalfWord;
DMA_InitStructure.DMA_MemoryDataSize=DMA_MemoryDataSize_HalfWord;

DMA_InitStructure.DMA_Mode=DMA_Mode_Circular;
DMA_InitStructure.DMA_Priority=DMA_Priority_High;
DMA_InitStructure.DMA_M2M=DMA_M2M_Disable;

DMA_Init(DMA1_Channel1,&DMA_InitStructure);
DMA_Cmd(DMA1_Channel1,ENABLE);
}

void filter(void)
{
int sum=0;
u8 count,i;

for(i=0;i<2;i++)
{
for(count=0;count<N;count++)
{
   sum+=ADCData[i][count];
}
   ADCAVGData[i]=sum/N;
   sum=0;
}
}