21ic电子技术开发论坛 › 单片机与嵌入式系统 › 航顺HK32 MCU › 使用HK32F030驱动ST7567 LCD
返回列表 发新帖我要提问

[其他] 使用HK32F030驱动ST7567 LCD

[复制链接]
 楼主| 发给她更好fh 发表于 2022-12-28 12:02 | 显示全部楼层 |阅读模式
CD, LCD
本文使用的LCD是12864液晶屏，驱动IC是ST7567，本文记录如何驱动ST7567，这里要说明一点，LCD里面都有一个驱动器，驱动LCD，其实就是驱动里面的驱动IC。关于本文使用的LCD 6143263abbfccb4a3b.png


回复 赏

举报

相关帖子
 楼主| 发给她更好fh 发表于 2022-12-28 12:04 | 显示全部楼层
引脚说明
361463abc03e6fb6d.png
回复 赏

举报

 楼主| 发给她更好fh 发表于 2022-12-28 12:05 | 显示全部楼层
关于ST7567的驱动命令
7171263abc050cbd21.png
回复 赏

举报

 楼主| 发给她更好fh 发表于 2022-12-28 14:17 | 显示全部楼层
驱动时序 5267463abdf84206fd.png
回复 赏

举报

 楼主| 发给她更好fh 发表于 2022-12-28 14:19 | 显示全部楼层
可以看出：
CSB也就是引脚CS，片选引脚，为低电平的时候，才能写入数据或命令；
A0也就是引脚RS，数据或命令选择引脚；
SCL时钟引脚，为低电平期间，写入数据，
SDA数据引脚，数据低位在前，高位在后；
回复 赏

举报

 楼主| 发给她更好fh 发表于 2022-12-28 14:22 | 显示全部楼层
复位时序 9822163abe08ca03e4.png
回复 赏

举报

 楼主| 发给她更好fh 发表于 2022-12-28 14:23 | 显示全部楼层
RSTB也就是RES，复位引脚，拉低即可复位，但是要注意拉低再拉高后要延时一段时间才能操作LCD。
回复 赏

举报

 楼主| 发给她更好fh 发表于 2022-12-28 14:24 | 显示全部楼层
原理图
651163abe1217d9f3.png
回复 赏

举报

 楼主| 发给她更好fh 发表于 2022-12-28 14:25 | 显示全部楼层
完整代码
复制
  1. #define LCD_SCL_PORT         GPIOB
    

  2. #define LCD_SCL_PIN          GPIO_Pin_10
    


  3. 

  4. #define LCD_SDA_PORT         GPIOB
    

  5. #define LCD_SDA_PIN          GPIO_Pin_11
    


  6. 

  7. #define LCD_POWER_PORT       GPIOB
    

  8. #define LCD_POWER_PIN        GPIO_Pin_12
    


  9. 

  10. #define LCD_CS_PORT          GPIOA 
    

  11. #define LCD_CS_PIN           GPIO_Pin_5
    


  12. 

  13. #define LCD_RST_PORT         GPIOA
    

  14. #define LCD_RST_PIN          GPIO_Pin_6
    


  15. 

  16. #define LCD_RS_PORT                GPIOA
    

  17. #define LCD_RS_PIN                 GPIO_Pin_7   //A0
    


  18. 

  19. #define LCD_CMD                       0
    

  20. #define LCD_DATA             1
    

  21.                                                 
    

  22. #define PORT(port)                LCD_##port##_PORT
    

  23. #define PIN(pin)                  LCD_##pin##_PIN
    


  24. 

  25. #define LCD_MAX_HEIGHT_BIT         64
    

  26. #define LCD_MAX_WIDTH_BIT    128
    

  27. #define LCD_MAX_HEIGHT             LCD_MAX_HEIGHT_BIT/16
    

  28. #define LCD_MAX_WIDTH        LCD_MAX_WIDTH_BIT/8
    


  29. 

  30.                                                         
    

  31. #define LCD_PIN_OUT(pin,level) { if(level)                               \
    

  32.                                                              { GPIO_SetBits(PORT(pin),PIN(pin));}    \
    

  33.                                                              else                                    \
    

  34.                                                              { GPIO_ResetBits(PORT(pin),PIN(pin));}  \
    

  35.                                }        
    

  36. static void LcdIoInit(void)
    

  37. {
    

  38.         RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA, ENABLE);
    

  39.         RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOB, ENABLE);
    


  40. 

  41.         GPIO_InitTypeDef        GPIO_InitStructure;
    


  42. 

  43.         GPIO_InitStructure.GPIO_Pin = LCD_SCL_PIN|LCD_SDA_PIN|LCD_POWER_PIN ;
    

  44.         GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
    

  45.         GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
    

  46.         GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    

  47.         GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
    

  48.         GPIO_Init(GPIOB, &GPIO_InitStructure);
    

  49.                 
    

  50.         GPIO_InitStructure.GPIO_Pin = LCD_CS_PIN|LCD_RST_PIN|LCD_RS_PIN ;
    

  51.         GPIO_Init(GPIOA, &GPIO_InitStructure);
    

  52. }                                                           
    

  53.                                                                                                                                                                               
    

  54. /*
    

  55. ismcd:高为数据，低为指令
    

  56. */
    

  57. static void LcdWrite(uint8_t iscmd ,uint8_t data)
    

  58. {
    

  59.         uint8_t  i;
    

  60.         
    

  61.         LCD_PIN_OUT(CS,0);
    

  62.         
    

  63.         LCD_PIN_OUT(RS,iscmd);
    


  64. 

  65.         for(i=0;i<8;i++)
    

  66.         {
    

  67.                 if(data&0x80)
    

  68.                 {
    

  69.                         LCD_PIN_OUT(SDA,1);
    

  70.                 }
    

  71.                 else
    

  72.                 {
    

  73.                         LCD_PIN_OUT(SDA,0);
    

  74.                 }
    

  75.                 LCD_PIN_OUT(SCL,0);
    

  76.                 DelayUs(10); 
    

  77.                 LCD_PIN_OUT(SCL,1);
    

  78.                 DelayUs(10);
    

  79.                 data=data<<1;
    

  80.         }
    

  81.         
    

  82.         LCD_PIN_OUT(CS,1);
    

  83. }                                           
    

  84.                 
    

  85. /*
    

  86. page   :0-7
    

  87. column :0-127
    

  88. */
    

  89. static void LcdAddress(uint8_t  page,uint8_t column) 
    

  90. {
    

  91.         LcdWrite(LCD_CMD,0xb0+page); 
    

  92.         LcdWrite(LCD_CMD,((column>>4)&0x0f)+0x10); //设置列地址的高4 位 
    

  93.         LcdWrite(LCD_CMD,((column>>0)&0x0f)+0x00); //设置列地址的低4 位
    

  94. }
    


  95. 

  96. /*全屏清屏*/ 
    

  97. void LcdClearScreen(void) 
    

  98. {
    

  99.         uint8_t  i,j; 
    

  100.         
    

  101.         for(i=0;i<8;i++) 
    

  102.         {
    

  103.                 LcdAddress(i,0);
    

  104.                 
    

  105.                 for(j=0;j<128;j++) 
    

  106.                 {
    

  107.                         LcdWrite(LCD_DATA,0x0); 
    

  108.                 }
    

  109.         }
    

  110. }
    


  111. 


  112. 

  113. /*清屏某一行*/ 
    

  114. void LcdClearScreenLine(uint8_t line) 
    

  115. {
    

  116.         uint8_t  j; 
    

  117.         
    

  118.         LcdAddress(line,0);
    

  119.                 
    

  120.         for(j=0;j<128;j++) 
    

  121.         {
    

  122.                 LcdWrite(LCD_DATA,0x0); 
    

  123.         }
    

  124. }
    


  125. 


  126. 

  127. void LcdDispBK(void) 
    

  128. {
    

  129.         uint8_t  i;
    

  130.         //上框 
    

  131.         LcdAddress(0,0); 
    

  132.         for (i=0;i<128;i++) 
    

  133.         {
    

  134.                 LcdWrite(LCD_DATA,0x01); 
    

  135.         }
    

  136.         //下框 
    

  137.         LcdAddress(7,0); 
    

  138.         for (i=0;i<128;i++) 
    

  139.         {
    

  140.                 LcdWrite(LCD_DATA,0x80); 
    

  141.         }
    

  142.         
    

  143.         //左框 
    

  144.         for(i=0;i<8;i++) 
    

  145.         {
    

  146.                 LcdAddress(i,0); 
    

  147.                 LcdWrite(LCD_DATA,0xff); 
    

  148.         }
    

  149.         //右框 
    

  150.         for(i=0;i<8;i++) 
    

  151.         {
    

  152.                 LcdAddress(i,127); 
    

  153.                 LcdWrite(LCD_DATA,0xff); 
    

  154.         }
    

  155. }
    


  156. 


  157. 

  158. void LcdDispStr8x16(uint8_t reverse,uint8_t page,uint8_t column,uint8_t *str) 
    

  159. {
    

  160.         uint16_t i=0,j=0,k=0;
    

  161.         
    

  162.         while(str[i]>0x00) 
    

  163.         {
    

  164.                 if((str[i]>=0x20)&&(str[i]<=0x7e)) 
    

  165.                 {
    

  166.                         j=str[i]-0x20; 
    

  167.                         LcdAddress(page,column); //上半部分
    

  168.                         for(k=0;k<8;k++) 
    

  169.                         {
    

  170.                                 if (reverse==1) 
    

  171.                                 {
    

  172.                                         LcdWrite(LCD_DATA,Ascii_8x16[j][k]);
    

  173.                                 }
    

  174.                                 else 
    

  175.                                 {
    

  176.                                         LcdWrite(LCD_DATA,~(Ascii_8x16[j][k])); 
    

  177.                                 }
    

  178.                         }
    

  179.                         LcdAddress(page+1,column);//下半部分
    

  180.                         
    

  181.                         for(k=0;k<8;k++) 
    

  182.                         {
    

  183.                                 if (reverse==1) 
    

  184.                                 {
    

  185.                                         LcdWrite(LCD_DATA,Ascii_8x16[j][k+8]);
    

  186.                                 }
    

  187.                                 else 
    

  188.                                 {
    

  189.                                         LcdWrite(LCD_DATA,~(Ascii_8x16[j][k+8])); 
    

  190.                                 }
    

  191.                         }
    

  192.                         i++; 
    

  193.                         column+=8;
    

  194.                 }
    

  195.         }
    

  196. }
    


  197. 

  198. void LcdDispNum16x32(uint8_t reverse,uint8_t page,uint8_t column,uint8_t *str) 
    

  199. {
    

  200.         uint16_t i=0,j=0,k=0,n=0;
    

  201.         
    

  202.         while(str[i]>0x00) 
    

  203.         {
    

  204.                 if((str[i]>=0x30)&&(str[i]<=0x39)) 
    

  205.                 {
    

  206.                         j=str[i]-0x30; 
    

  207.                 }
    

  208.                 else
    

  209.                 {
    

  210.                         if(str[i]==' ')
    

  211.                         {
    

  212.                                 j=10;
    

  213.                         }
    

  214.                         else
    

  215.                         {
    

  216.                                 return;
    

  217.                         }
    

  218.                 } 
    

  219.                 for(n=0;n<4;n++)
    

  220.                 {
    

  221.                         LcdAddress(page+n,column); //上半部分
    

  222.                         for(k=0;k<16;k++) 
    

  223.                         {
    

  224.                                 if (reverse==1) 
    

  225.                                 {
    

  226.                                         LcdWrite(LCD_DATA,Num16X32[j][k+n*16]);
    

  227.                                 }
    

  228.                                 else 
    

  229.                                 {
    

  230.                                         LcdWrite(LCD_DATA,~(Num16X32[j][k+n*16])); 
    

  231.                                 }
    

  232.                         }
    

  233.                 }
    

  234.                 i++; 
    

  235.                 column+=16;
    

  236.         }
    

  237. }
    


  238. 

  239. void LcdInit(void)
    

  240. {
    

  241.         LcdIoInit();
    

  242.         
    

  243.         LCD_PIN_OUT(POWER,1);
    

  244.         DelayMs(100);
    

  245.         
    

  246.         LCD_PIN_OUT(RST,0);
    

  247.         DelayMs(20); 
    

  248.         LCD_PIN_OUT(RST,1);     /*复位完毕*/ 
    

  249.         DelayMs(20); 
    

  250.                 
    

  251.         LcdWrite(LCD_CMD,0xe2);         /*软复位*/
    

  252.         LcdWrite(LCD_CMD,0x2c);  /*升压步聚1*/        
    

  253.         LcdWrite(LCD_CMD,0x2e);  /*升压步聚2*/
    

  254.         LcdWrite(LCD_CMD,0x2f);  /*升压步聚3*/
    

  255.         LcdWrite(LCD_CMD,0x25);  /*粗调对比度，可设置范围0x20～0x27*/
    

  256.         LcdWrite(LCD_CMD,0x81);  /*微调对比度*/
    

  257.         LcdWrite(LCD_CMD,0x10);  /*0x1a,微调对比度的值，可设置范围0x00～0x3f*/
    

  258.         LcdWrite(LCD_CMD,0xa2);  /*1/9偏压比（bias）*/
    

  259.         LcdWrite(LCD_CMD,0xc8);  /*行扫描顺序：从上到下*/
    

  260.         LcdWrite(LCD_CMD,0xa0);  /*列扫描顺序：从左到右*/
    

  261.         LcdWrite(LCD_CMD,0x40);  /*起始行：第一行开始*/
    

  262.         LcdWrite(LCD_CMD,0xaf);  /*开显示*/
    

  263.         
    

  264.         LcdClearScreen();
    

  265.         
    

  266.         LcdDispStr8x16(1,3,40,(uint8_t *)"LCD12864");
    

  267.         LcdDispStr8x16(0,6,20,(uint8_t *)"1234567890");
    

  268. //        while(1);
    

  269. }
    


  270. 

  271. //本文使用的取模方式为：阴码、逆向、列行式
    

  272. const unsigned char Ascii_8x16[][16]=          
    

  273. {
    

  274. {0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
    

  275. {0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00},/*"!",1*/
    

  276. {0x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*""",2*/
    

  277. {0x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00},/*"#",3*/
    

  278. {0x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00,0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00},/*"$",4*/
    

  279. {0xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00,0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00},/*"%",5*/
    

  280. {0x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10},/*"&",6*/
    

  281. {0x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
    

  282. {0x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00},/*"(",8*/
    

  283. {0x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00},/*")",9*/
    

  284. {0x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00},/*"*",10*/
    

  285. {0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00},/*"+",11*/
    

  286. {0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00},/*",",12*/
    

  287. {0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01},/*"-",13*/
    

  288. {0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00},/*".",14*/
    

  289. {0x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04,0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00},/*"/",15*/
    

  290. {0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00},/*"0",16*/
    

  291. {0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"1",17*/
    

  292. {0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00},/*"2",18*/
    

  293. {0x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00},/*"3",19*/
    

  294. {0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00},/*"4",20*/
    

  295. {0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00},/*"5",21*/
    

  296. {0x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00},/*"6",22*/
    

  297. {0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00},/*"7",23*/
    

  298. {0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00},/*"8",24*/
    

  299. {0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00},/*"9",25*/
    

  300. {0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00},/*":",26*/
    

  301. {0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00},/*";",27*/
    

  302. {0x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00},/*"<",28*/
    

  303. {0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00},/*"=",29*/
    

  304. {0x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00},/*">",30*/
    

  305. {0x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00,0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00},/*"?",31*/
    

  306. {0xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00},/*"@",32*/
    

  307. {0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20},/*"A",33*/
    

  308. {0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00},/*"B",34*/
    

  309. {0xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00},/*"C",35*/
    

  310. {0x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00},/*"D",36*/
    

  311. {0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00},/*"E",37*/
    

  312. {0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00},/*"F",38*/
    

  313. {0xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00},/*"G",39*/
    

  314. {0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20},/*"H",40*/
    

  315. {0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"I",41*/
    

  316. {0x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00},/*"J",42*/
    

  317. {0x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00},/*"K",43*/
    

  318. {0x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00},/*"L",44*/
    

  319. {0x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00},/*"M",45*/
    

  320. {0x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00},/*"N",46*/
    

  321. {0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00},/*"O",47*/
    

  322. {0x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00},/*"P",48*/
    

  323. {0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00},/*"Q",49*/
    

  324. {0x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20},/*"R",50*/
    

  325. {0x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00},/*"S",51*/
    

  326. {0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00},/*"T",52*/
    

  327. {0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00},/*"U",53*/
    

  328. {0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00},/*"V",54*/
    

  329. {0xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00,0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00},/*"W",55*/
    

  330. {0x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20},/*"X",56*/
    

  331. {0x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00},/*"Y",57*/
    

  332. {0x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00},/*"Z",58*/
    

  333. {0x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00},/*"[",59*/
    

  334. {0x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00},/*"",60*/
    

  335. {0x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00},/*"]",61*/
    

  336. {0x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
    

  337. {0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80},/*"_",63*/
    

  338. {0x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
    

  339. {0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20},/*"a",65*/
    

  340. {0x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00},/*"b",66*/
    

  341. {0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00},/*"c",67*/
    

  342. {0x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00,0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20},/*"d",68*/
    

  343. {0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00},/*"e",69*/
    

  344. {0x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"f",70*/
    

  345. {0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00},/*"g",71*/
    

  346. {0x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20},/*"h",72*/
    

  347. {0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"i",73*/
    

  348. {0x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00},/*"j",74*/
    

  349. {0x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00},/*"k",75*/
    

  350. {0x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"l",76*/
    

  351. {0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F},/*"m",77*/
    

  352. {0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20},/*"n",78*/
    

  353. {0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00},/*"o",79*/
    

  354. {0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00},/*"p",80*/
    

  355. {0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80},/*"q",81*/
    

  356. {0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00},/*"r",82*/
    

  357. {0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00},/*"s",83*/
    

  358. {0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00},/*"t",84*/
    

  359. {0x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20},/*"u",85*/
    

  360. {0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00},/*"v",86*/
    

  361. {0x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00},/*"w",87*/
    

  362. {0x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00},/*"x",88*/
    

  363. {0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00},/*"y",89*/
    

  364. {0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00},/*"z",90*/
    

  365. {0x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02,0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40},/*"{",91*/
    

  366. {0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00},/*"|",92*/
    

  367. {0x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00,0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00},/*"}",93*/
    

  368. {0x00,0x06,0x01,0x01,0x02,0x02,0x04,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"~",94*/
    

  369. };
回复 赏

举报

 楼主| 发给她更好fh 发表于 2022-12-28 23:07 | 显示全部楼层
显示测试
1848863ac5b9f378c8.png
回复 赏

举报

AloneKaven 发表于 2023-1-3 16:18 | 显示全部楼层
要延时多久才能操作LCD啊？
回复 赏

举报

返回列表 发新帖
高级模式
B Color Image Link Quote Code Smilies
您需要登录后才可以回帖 登录 | 注册

本版积分规则

发给她更好fh

43

主题

563

帖子

1

粉丝
快速回复 在线客服 返回列表 返回顶部