基于CC2640R2F的按键开发

发表于 2020-2-2 16:14

实现功能
短按进入NB模式，长按3s左右进入BLE模式，长按5s关机。

实现步骤
首先按键作为一个输入设备，我们应该把IO口设置成输入上拉模式，其次还涉及到消抖处理，防止误触发。由于该按键需实现长短按，于是把IO口设置成双边沿触发中断，具体实现如下：

//配置IO位输入上拉模式

PIN_Config keyPinsCfg[] =
{
Board_WakeUpKey | PIN_GPIO_OUTPUT_DIS  | PIN_INPUT_EN  |  PIN_PULLUP,

PIN_TERMINATE
};

//注册按键回调函数

Board_initKeys(SimpleBLEPeripheral_keyChangeHandler);

//按键初始化

void Board_initKeys(keysPressedCB_t appKeyCB)
{
  // Initialize KEY pins. Enable int after callback registered
  KeyHandle = PIN_open(&KeyState, keyPinsCfg);
  PIN_registerIntCb(KeyHandle, Board_keyCallback); //注册中断，中断触发进入Board_keyCallback函数
//定义中断触发条件
  PIN_setConfig(KeyHandle,  PIN_BM_IRQ, Board_WakeUpKey | PIN_IRQ_BOTHEDGES); //电源按键

#ifdef POWER_SAVING //低功耗状态唤醒
  //Enable wakeup
  PIN_setConfig(KeyHandle,  PINCC26XX_BM_WAKEUP, Board_WakeUpKey | PINCC26XX_WAKEUP_NEGEDGE);
#endif //POWER_SAVING

  // Setup keycallback for keys  消抖
  Util_constructClock(&keyChangeClock, Board_keyChangeHandler,
                  KEY_DEBOUNCE_TIMEOUT, 0, false, 0);  //手动定时器
  // Set the application callback
  //appKeyCB 入队列的函数指针
  appKeyChangeHandler = appKeyCB; //通知APP层，有按键触发
}

发表于 2020-2-2 16:15

具体思路
1 //按键消抖，延时16ms处理

static void Board_keyCallback(PIN_Handle hPin, PIN_Id pinId)
{
  Util_restartClock(&keyChangeClock, 16);          //启动定时器，延时消抖
  PIN_clrPendInterrupt(hPin, pinId);  //清中断
}

//按键消抖后，长短按键处理
static void Board_keyChangeHandler(UArg a0)
{
  uint8_t key_pressed = 0;

2 //检测到下降沿触发，打开定时器
  if (!PIN_getInputValue(Board_WakeUpKey))
  {
   Util_startClock(&keyTime_periodicClock);  //启动定时器，判断长短按键
   key_time = 0;
  }
  else
  {

4 //按键上升沿触发，关闭定时器，事件入队列
   Util_stopClock(&keyTime_periodicClock);
   if (appKeyChangeHandler != NULL)
   {
   if (key_time <= 2)
   {
         key_pressed |= KEY_SHORT;
   }
   else if ((key_time > 2) && (key_time <= 5))
   {
         key_pressed |= KEY_LONG;
   }
   else
   {
         key_pressed |= KEY_TOO_LONG;
   }
   }
// Notify the application  入队列
(*appKeyChangeHandler)(key_pressed);
  }
}

3 //APP任务中处理定时器，设定为1s定时器，定时到则key_time++，指示灯亮则松手触发按键的上升沿中断

   case SBP_KEY_TIME_EVT:
      events &= ~SBP_KEY_TIME_EVT; //清事件ID
      key_time++;
      if (key_time == 3)
      {
         HwGPIOSet(Board_GLED, 1);  //绿LED指示3s到
         Util_startClock(&one_second);
      }
      else if (key_time == 6)
      {
         HwGPIOSet(Board_RLED, 1);  //红LED指示6s到
         Util_startClock(&one_second);
      }
      else
      {
         //do nothing
      }
      break;

5 //按键回调函数，入队列

void SimpleBLEPeripheral_keyChangeHandler(uint8 keys)
{
  SimpleBLEPeripheral_enqueueMsg(SBP_KEY_CHANGE_EVT, keys);
}

//入队列函数

static void SimpleBLEPeripheral_enqueueMsg(uint8_t event, uint8_t state)
{
  sbpEvt_t *pMsg;
  // Create dynamic pointer to message.
  if ((pMsg = ICall_malloc(sizeof(sbpEvt_t))))
  {
pMsg->hdr.event = event;
pMsg->hdr.state = state;
// Enqueue the message.
Util_enqueueMsg(appMsgQueue, syncEvent, (uint8*)pMsg);
  }
}

6 //出队列
  case SBP_QUEUE_EVT:
      events &= ~SBP_QUEUE_EVT;
      while (!Queue_empty(appMsgQueue))
      {
         sbpEvt_t *pMsg = (sbpEvt_t *)Util_dequeueMsg(appMsgQueue);
         if (pMsg)
         {
         // Process message.
         SimpleBLEPeripheral_processAppMsg(pMsg);
         // Free the space from the message.
         ICall_free(pMsg);
         }
      }

static void SimpleBLEPeripheral_processAppMsg(sbpEvt_t *pMsg)
{
  switch (pMsg->hdr.event)
  {
case SBP_STATE_CHANGE_EVT:
   SimpleBLEPeripheral_processStateChangeEvt((gaprole_States_t)pMsg->
                                             hdr.state);
   break;

case SBP_CHAR_CHANGE_EVT:
   SimpleBLEPeripheral_processCharValueChangeEvt(pMsg->hdr.state);
   break;

case SBP_KEY_CHANGE_EVT:  //按键处理
   SimpleBLEPeripheral_handleKeys(pMsg->hdr.state);
   break;

default:
   break;
  }
}

7 //APP处理不同的按键事件

static void SimpleBLEPeripheral_handleKeys(uint8_t keys)
{
  switch (keys)
  {
  case KEY_SHORT:

break;
  //打开蓝牙
  case KEY_LONG:

break;
  //断电，切换管理员
  case KEY_TOO_LONG:

break;

发表于 2020-2-2 16:15

思路总结

当按键按下，检测到下降沿中断触发，消抖后，打开定时器，计时，3s时间到绿灯亮或则6时间到红灯亮，松手，检测到上升沿中断触发，消抖后，关闭定时器，将对应事件加入队列中，唤醒APP任务，出队列，进行相应的事件处理。

发表于 2020-3-1 11:42

非常感谢楼主分享

发表于 2020-3-1 11:47

非常感谢楼主分享

发表于 2020-3-1 12:09

非常感谢楼主分享

发表于 2020-3-1 12:14

非常感谢楼主分享

发表于 2020-3-1 12:17

非常感谢楼主分享

[CC2640] 基于CC2640R2F的按键开发

相关帖子

浏览过的版块